Double Hanging Egg Chair Covers: Fit Twin Pods, Stand Arcs, Springs, and Bases

A double hanging egg chair places two suspended pods, or one wide twin seat, inside a tall curved stand. The frame, springs, chains, cushions, and moving basket create a profile that changes whenever the chair swings. A custom double hanging egg chair with stand cover should be based on one stable parked position, not the widest point the chair can reach in motion.

Before measuring, remove loose pillows, dry the weave, and stop the seat from swinging. Confirm that the stand is level and structurally sound. The cover is for storage protection only. Nobody should sit in the chair, and the chair should not move, while the cover is installed.

Choose One Repeatable Parked Position

Center the twin basket beneath the suspension points and decide whether the front edge sits level, slightly reclined, or secured against a soft spacer. Photograph the chosen position from every side. A changing parked angle alters the total depth and can make the finished cover look either tight or excessively loose.

Measure the Stand Before the Seat

Follow How to Measure and record maximum stand height, outside base width, base depth, arm spacing, and the highest suspension hardware. Measure rigid metal points first. The frame defines the cover’s load-bearing outline, while the woven seat needs breathing room inside that outline.

Map Both Pods and the Center Valley

Measure the outer width of both pods together, each pod’s front-to-back depth, and the dip or valley between them. For one wide two-person basket, note the deepest curve, high side wings, and center cushion crown. Avoid pulling fabric tightly across the center because rainwater can collect in a flat bridge.

Document Springs, Chains, and Hooks

Record every spring, chain, carabiner, hook, and safety cable in its normal storage position. Note exposed metal edges and moving joints that need clearance or reinforcement. Do not use the cover to carry the seat’s weight, and do not route a tie-down through the suspension hardware.

Set Cushion and Pillow Rules

Decide which cushions remain in place and arrange them consistently. Thick headrests or loose lumbar pillows can add height, create pressure points, and hold moisture. If cushions are stored separately, measure the empty basket and state that clearly in the production brief.

Shape the Roof for Runoff

The curved stand usually creates a tall center or rear ridge. Plan a gentle roof line that sends water toward open sides instead of into the valley between pods. An approved support can reduce pooling, but it must have a broad, smooth top that cannot abrade the fabric or deform the weave.

Select Fabric for Woven Surfaces

Compare UV exposure, water behavior, flexibility, weight, and cleaning instructions on Our Fabrics. A soft interior and reinforced contact zones help around wicker rims, stand shoulders, spring ends, and base corners. Browse Patio Furniture Covers for related protection options.

Plan Handles, Vents, and Removal

Place handles where two people can lift the tall cover without dragging it across the basket. Covered vents work best in sheltered side zones, away from the roof’s runoff path. A long opening or zipper can help the cover clear the curved stand, but it should close without loading the springs or chains.

Anchor to the Base Without Blocking Motion

Use stable base rails or approved lower frame points for straps. Keep buckles away from paving, feet, and walking paths. Never tighten the cover around a moving seat, and never treat tie-downs as a substitute for the chair manufacturer’s wind and anchoring instructions.

Prepare a Twin-Chair Production Brief

Send the parked-position photos, stand dimensions, basket envelope, center valley, suspension hardware, cushion plan, runoff direction, opening preference, vent locations, and anchor points. Review the Double Hanging Egg Chair with Stand Cover page, then request a quote if the frame has unusual geometry.

Frequently Asked Questions

Should the chair be measured while it is swinging?

No. Immobilize the basket in one normal storage position and measure the repeatable parked envelope.

Can the cover support the hanging basket?

No. The stand and suspension system must support the seat. The cover should carry no furniture load.

Should cushions stay under the cover?

Only when they are completely dry, consistently arranged, and included in every height and depth measurement.

Turn the Measurements Into a Production-Ready Cover

A reliable twin egg-chair cover begins with a stable seat position and a frame-first measurement plan. When the stand arcs, paired pods, suspension hardware, cushions, runoff path, and base anchors are documented separately, the finished cover is easier to install and less likely to press on delicate woven surfaces. Use the product page and measurement resources above to organize a clear request for CoversForge.