Wicker Recliner Covers: Measure Footrests, Curved Weave, Motion Bases, and Handles

Warm gray fitted cover over a single wicker patio recliner with its footrest closed on a bright covered terrace
By Published On: September 26, 2026

A wicker recliner combines a curved woven shell with a [...]


A wicker recliner combines a curved woven shell with a moving back, a folding footrest, and a compact mechanical base. Those layers create very different outlines when the chair is upright, reclined, or partly open. A custom wicker recliner cover should be based on one safe parked position and should protect the weave without pulling the mechanism out of alignment.

Clean the chair, let the wicker and cushions dry, close the footrest, and return the back to the manufacturer-approved storage angle. Disconnect power if the model uses a motor and the manufacturer requires it. Never operate the recliner while the cover is installed, and keep cords, controls, and pinch zones accessible for inspection.

Warm gray fitted cover over a single wicker patio recliner with its footrest closed on a bright covered terrace

Choose One Repeatable Parked Position

Decide whether the chair will be stored fully upright, slightly reclined, or in another approved position. Engage any transport or swivel lock provided by the manufacturer. Photograph the chair from both sides so the back angle, footrest seam, handle position, and base relationship can be reproduced each time.

Measure the Upright Envelope

Follow How to Measure and record maximum width across the arms, overall depth from the back curve to the front edge, and height from the floor to the highest back point. Measure at several heights because flared wicker arms can be wider above the seat than at the feet.

Capture the Closed Footrest

Measure the footrest width, thickness, front curve, lower clearance, and seam where it meets the seat. Confirm that it is fully latched before measuring. The cover needs gentle ease across this junction so it does not wedge into the gap or pull the footrest open when removed.

Trace Wicker Curves and Fragile Edges

Record rolled arms, braided trim, open lattice, decorative peaks, and loose ends. Wicker should not serve as an anchor point. Mark brittle or repaired areas for padding and avoid a skin-tight pattern that rubs the weave every time wind moves the fabric.

Map Handles, Buttons, and Power Leads

Note manual release handles, side levers, power buttons, battery packs, transformers, and cable exits. Store electrical components according to their instructions and keep them dry. If a control must remain accessible, define a protected flap rather than leaving an uncontrolled gap.

Include the Motion Base and Feet

Measure the swivel ring, rocker rails, pedestal, feet, and widest lower sweep. A compact seat can sit on a surprisingly broad base. Keep the hem above moving parts and the ground, and do not route straps through a mechanism or across a surface that rotates.

Decide How Cushions Will Be Stored

State whether loose seat, back, or lumbar cushions remain on the chair. Cushions change height, front projection, and moisture behavior. If they are removed, measure the chair without them and store the cushions separately in a dry location rather than letting empty fabric collapse into the seat well.

Choose a Weave-Friendly Material

Compare manageable weight, interior smoothness, UV resistance, water behavior, and cleaning needs on Our Fabrics. Browse Patio Furniture Covers. A softer handling profile can reduce abrasion on raised wicker texture, while reinforced zones protect the cover at hard trim and handle edges.

Secure the Cover Without Restricting Motion

Use straps at stable legs or the fixed portion of the base only when approved. Keep buckles clear of the footrest hinge, swivel track, rocker arc, power cable, and floor. After installation, confirm the chair is dry, the cover cannot reach the mechanism, and the recliner will not be used while covered.

Send a Recliner-Specific Fit Packet

Provide the brand and model, parked position, back angle, arm width, seat and footrest geometry, wicker details, base, controls, power components, cushion plan, hem height, safe anchors, exposure, and labeled photos. Review the Wicker Recliner Custom Covers page before ordering.

Frequently Asked Questions

Should the footrest be open for measuring?

Use the manufacturer-approved storage position. In most cases the footrest should be fully closed and latched.

Can straps wrap around the wicker arms?

No. Anchor only to stable structural points that will not damage the weave or interfere with the mechanism.

Can the recliner be used under the cover?

No. Remove the cover completely before sitting, reclining, rocking, swiveling, or operating powered controls.

Turn the Measurements Into a Production-Ready Brief

A wicker recliner cover depends on a controlled storage state. The back angle, closed footrest, delicate weave, control hardware, motion base, cushions, safe anchors, and dry installation routine must work together so weather protection does not become a mechanical or abrasion problem. Request a Quote when the measurements and photographs are ready.

Share This Article

Written by : CoversForge

Leave A Comment

Follow Us

Uncover Convenience

We've got you covered, 
no matter what!

Latest Articles