Poolside Chaise Pair Covers: Fit Twin Loungers, Umbrella Tables, and Shared Footprints

Two chaise lounges and a small umbrella table create one wide, interrupted footprint. The seat backs may recline at different angles, the table can sit above or below the cushions, and the umbrella pole passes through the center. A custom poolside chaise pair with umbrella table cover needs a recorded furniture arrangement, not just the dimensions of one lounger doubled.

Set the furniture on a level, dry deck in the exact storage position. Close the umbrella, remove loose cushions if they will be stored elsewhere, and let wet surfaces dry. Never cover a raised umbrella in wind or use the cover as a restraint for furniture that should be independently anchored.

Lock the Pair Into One Repeatable Layout

Place the chaise lounges parallel and square to the pool edge, then center the table between them. Record the gap from each chaise to the table and mark the front. If staff move the furniture daily, add discreet deck reference points so the same shared footprint can be restored before installation.

Measure Each Chaise at Its Storage Angle

Follow How to Measure and record each lounger separately. Measure overall length, maximum width, seat height, back height, back angle, arm projections, wheels, and foot profile. Do not assume the pair is identical after repairs, replacement cushions, or different recline settings.

Map the Umbrella Table and Pole

Measure the table diameter or side lengths, top height, base spread, pole diameter, and pole offset from the shared centerline. Record the closed umbrella bundle at its widest point. A reinforced pole opening must fit the parked bundle without rubbing, leaking excessively, or carrying wind load.

Build the Combined Plan View

Sketch the outside perimeter around both chaise lounges and the center table. Add the narrow gaps where water or leaves could collect. Measure total length and width, then confirm diagonals from opposite corners. The cover should follow the three-part geometry without bridging so tightly that it presses on cushions.

Choose a Controlled Drainage Direction

Create a gentle high point over a stable furniture surface and direct runoff away from the pool and walking route. Avoid unsupported fabric valleys between the loungers and table. The cover must not drain chlorinated water back onto hardware or create a low pocket that becomes heavy after a storm.

Protect Poolside Materials and Finishes

Chlorine residue, sunscreen, salt, and damp towels can mark fabric and metal. Clean and dry the furniture before covering. Use smooth reinforcement where the pattern crosses hard arm corners or table rims, and keep the hem above puddles, deck chemicals, and abrasive coping edges.

Select Fabric and Wind Controls

Compare finished weight, UV resistance, water behavior, flexibility, and abrasion performance on Our Fabrics. Browse Patio Furniture Covers for related applications. Place straps at stable legs or approved anchors, never around the umbrella crank, tilt joint, pool rail, or moving back mechanism.

Plan Installation From the Center Out

Align the reinforced pole opening first, settle the table panel, and then lower the two chaise wings evenly. Guide seams over the backrests instead of pulling from the feet. Two people should install a wide cover so it does not drag on the deck or snag the umbrella hardware.

Record Seasonal Changes

State whether thick cushions, head pillows, wheels, side trays, or towel bars remain in place. A low winter storage profile may differ from the summer service layout. If both configurations matter, provide separate measurements and photographs rather than expecting one tight pattern to fit two different envelopes.

Assemble the Production Brief

Send the labeled plan view, chaise dimensions, back angles, table and pole measurements, closed umbrella profile, hem plane, drainage direction, safe anchor points, exposure, and photographs. Review the product page before approving the final arrangement.

Frequently Asked Questions

Can the umbrella remain open under the cover?

No. Close and secure the umbrella according to its manufacturer before measuring or covering. The cover is not a wind restraint.

Should the two chaise backs use the same angle?

A matching, repeatable storage angle simplifies the pattern and installation. If the angles must differ, label and measure each side separately.

Can wet cushions stay under the cover?

Let cushions and frames dry first. Trapped moisture can encourage staining, odor, and corrosion even when the outer fabric sheds rain.

Turn the Measurements Into a Production-Ready Brief

One documented furniture layout turns three separate poolside pieces into a predictable cover shape. Accurate back angles, table and pole geometry, runoff planning, safe anchors, and a repeatable installation routine support a cleaner fit and easier daily use. Request a Quote when the measurements and photographs are ready.