Double Chaise Daybed Covers: Fit Twin Backs, Center Consoles, Cushions, and Bases

A double chaise daybed combines two reclining profiles, a broad shared base, thick cushions, arms, a center console, and sometimes trays or cup holders. A custom outdoor double chaise daybed cover should follow the exact stored silhouette without flattening cushions, bridging unsupported gaps, or dragging across the pool deck.

Move the daybed away from the pool edge when the manufacturer and site allow, engage wheel or recliner locks, remove loose accessories, and let cushions and frame dry. Use two people for a wide unit. A cover is not a flotation device, child barrier, furniture restraint, or permission to leave unstable components assembled in severe weather.

Set Both Backs to One Storage Angle

Choose the manufacturer-approved covered position for the left and right reclining backs. Record the angle or indexed stop and photograph both sides. If the backs are asymmetrical, label them. Reproducing the same position prevents one panel from becoming tight while the other sags.

Measure the Overall Footprint

Use How to Measure to capture maximum width across arms, depth from front edge to rear frame, and height at each raised back. Record base length and diagonals. Measure the rigid furniture envelope, then note cushion projection separately.

Profile Each Chaise Independently

Measure left and right seat widths, front heights, back heights, hinge locations, and the transition from seat to back. Note bolster pillows, headrests, and lumbar cushions that remain. A paired sketch reveals differences that a single overall rectangle would hide.

Map the Center Console

Record console width, height, depth, lid or tray movement, cup holders, control panels, and gaps between the console and each chaise. Close and secure approved moving parts. The cover should bridge only spans that the furniture and chosen support method can safely carry.

Include Arms, Wings, and Side Tables

Measure curved arms, flared wings, integrated side tables, handles, towel rails, and removable trays. Record the largest side projection and corner radii. Store loose trays separately if they can lift, trap water, or create a hard abrasion point under fabric.

Decide Which Cushions Stay Installed

List seat, back, headrest, bolster, and decorative cushions. Confirm they are completely dry and supported in their normal positions. If cushions are stored elsewhere, measure the bare frame instead and label the photos so the production brief does not combine two configurations.

Record the Base, Feet, and Deck Gap

Map feet, sled bases, wheels, leveling pads, and low crossbars. Note deck slope and the desired hem clearance above splash zones. Closures should secure around approved lower geometry without crossing recliner mechanisms, sharp brackets, or drainage paths.

Choose Fabric for a Wide Low Profile

Compare finished weight, water behavior, UV resistance, flexibility, abrasion, and cleaning needs on Our Fabrics. Browse Patio Furniture Covers and Custom Covers. Wide furniture benefits from manageable fabric and clear orientation.

Plan Installation, Drainage, and Removal

Mark the console side and one front corner for orientation. Two adults can lower the cover over the raised backs and work forward without dragging it through water. Maintain a stable drainage slope, inspect after storms, and store the removed cover away from the pool walkway.

Build the Double-Chaise Brief

Send overall dimensions, separate left and right profiles, back settings, console details, arms, cushion list, base, feet, hem clearance, exposure, and labeled photos. Review the Outdoor Double Chaise Daybed Cover before final approval.

Frequently Asked Questions

Must both reclining backs be at the same angle?

Not necessarily, but each must be in a documented, repeatable, manufacturer-approved position every time the cover is used.

Can wet pool cushions stay under the cover?

No. Let cushions and the frame dry completely, and follow their care instructions before covering.

Is one overall width enough?

No. Record the twin profiles, center console, arms, and base because those features control panel shape and drainage.

Turn the Measurements Into a Production-Ready Brief

The useful measurement is not simply a wide daybed rectangle. Two stored back profiles, the console between them, cushion decisions, side projections, base geometry, and the poolside handling route give CoversForge a production-ready picture of the actual covered form. Include the normal furniture orientation and the clear walking space so installation never requires pulling fabric from the water side. Request a Quote when the measurements and photographs are ready.