Moon Chair Covers: Measure the Circular Frame, Bowl, Legs, and Fold

A moon chair is built around a broad circular frame, a deep fabric or woven bowl, and compact legs that may fold beneath the seat. That combination creates a very different profile from a straight-backed dining chair. A custom outdoor moon chair cover should follow the rigid rim and natural seat volume without pulling on folding joints or leaving a large pocket where water can settle.

Start with the chair clean, dry, and in the exact position used for storage. Remove the cover completely before sitting, folding, or carrying the chair. Follow the chair maker’s care and weather guidance; a cover does not increase the chair’s load rating, lock its frame, or make severe-wind exposure safe.

Identify the Moon Chair Construction

Record the model, rim material, seat material, frame layout, leg design, locking joints, and removable cushion. Photograph the front, back, side, and underside. Note whether the seat fabric is tensioned across the ring or supported by a deeper internal basket, because those forms require different depth measurements.

Choose Open or Folded Storage

Confirm whether the manufacturer permits the chair to remain open outdoors or recommends folding and indoor storage. Measure one approved, repeatable configuration only. If the chair folds, document the latch position and the folded thickness without forcing the frame tighter than its normal resting position.

Measure the Circular Rim as an Ellipse

Use How to Measure and record maximum outside width and height across the rigid rim. Many moon chairs look perfectly round from the front but measure slightly wider than tall. Take both dimensions and note any padded edge, projecting hinge, or uneven frame sleeve.

Capture Bowl Depth and Back Projection

Measure from the front rim plane to the deepest rear point with the chair unloaded. Record the seat’s lowest point and its distance from the ground. Do not press the flexible bowl flat. The pattern needs the chair’s natural stored volume so the cover can clear the seat without becoming a loose bag.

Map the Legs and Folding Hardware

Measure the widest foot spread, front-to-back footprint, ground clearance, hinge projections, braces, and locking tabs. Identify pinch points that must remain free. The hem should finish above the feet and moving joints so it cannot be trapped when the chair is handled.

Decide Whether the Cushion Stays

Clean and dry a removable cushion before deciding where it will be stored. Indoor storage normally reduces fading and moisture exposure. If the cushion remains in the chair, measure that exact arrangement and never compress it to create a tighter appearance.

Control Water on a Concave Shape

A moon chair naturally forms a basin. Shape the cover around the supported rim and discuss how the stored chair will shed water rather than hold it in the center. Keep the chair on a draining surface and never use improvised props that can slip, puncture fabric, or load the seat frame.

Select Fabric for Curves and Frequent Removal

Compare flexibility, water behavior, UV resistance, abrasion performance, and finished weight on Our Fabrics. Browse related Patio Furniture Covers. A supple material can follow the round rim and pack away more easily when the chair is used often.

Place Closures Below the Seat

Use only stable lower-frame locations approved for gentle hem control. Keep straps away from hinges, release levers, fabric seat edges, and walking paths. Cover closures limit ordinary fabric movement; they do not anchor the chair for storms or replace the maker’s relocation advice.

Send a Moon Chair Fit Brief

Provide the open or folded configuration, rim width and height, bowl depth, rear projection, foot spread, hinge details, cushion plan, ground clearance, exposure, and labeled photos. Review the Outdoor Moon Chair Cover or Request a Quote.

Frequently Asked Questions

Should a moon chair be measured like a round table?

No. Record the rim as a front-facing ellipse, then add bowl depth, rear projection, leg footprint, and folding hardware.

Can the cover stay on while the chair is folded?

Only if the folded position is manufacturer-approved and the cover was patterned for that exact configuration.

Should the seat cushion remain under the cover?

It can only be included if it is clean, fully dry, and always stored in the same position; indoor cushion storage is usually easier to manage.

Turn the Measurements Into a Clear Cover Brief

A dependable made-to-measure cover starts with one repeatable storage position, complete dimensions, labeled photos, safe-use limits, and a realistic handling routine. CoversForge can review fit, fabric, access, exposure, and quantity for the documented application. Request a Quote when the specification is ready.