Custom Outdoor Egg Chair Covers: Measure Curves, Cushions, and Hanging Frames

Egg chairs look simple from across a patio, but their deep curves, wide woven shells, cushions, and hanging frames make them difficult to protect with a generic rectangle. Custom outdoor egg chair covers work best when the cover follows the chair’s true outer envelope without becoming tight at the crown or loose around the base. A few careful decisions before ordering can make the cover easier to install, more secure in wind, and less likely to trap damp air.

Decide what the egg chair cover must protect

Start by defining the coverage boundary. A freestanding egg chair may have a circular base, a curved suspension arm, a hanging basket, and removable cushions. Some owners want one cover over the complete assembled chair. Others remove the cushions and cover only the frame and basket. The correct choice depends on storage space, how often the chair is used, and whether the cushions can be kept dry elsewhere.

For the cleanest one-piece solution, review the shape of the custom wicker egg chair cover and note every part that creates the maximum width, depth, or height. Do not measure only the woven basket if the stand extends farther.

Measure the chair in its normal storage position

Place the chair exactly where and how it will sit under the cover. Center the basket, arrange the cushions normally, and make sure the hanging chair is not swinging. Then record these dimensions:

• Overall height: from the floor to the highest point of the suspension arm or basket.
• Maximum width: across the widest point of the basket, arms, or base ring.
• Maximum depth: from the furthest forward cushion or basket edge to the back of the stand.
• Base footprint: the diameter or outside width and depth of the floor base.
• Basket width and height: useful for locating seams and vents around the curved shell.
• Suspension-arm offset: measure how far the arm sits behind or beside the basket centerline.

The general CoversForge measuring guide is a helpful starting point, but an egg chair benefits from a quick side photo and front photo with the critical dimensions marked.

Allow room around cushions and curved wicker

A cover should not compress thick cushions or scrape across raised wicker edges every time it is removed. At the same time, too much extra fabric can fold into pockets that collect water. Measure the chair with the cushions in the intended storage arrangement, then use a practical fit allowance rather than adding several inches to every dimension without a plan.

The crown deserves special attention. Egg chairs often narrow near the top, while the widest point sits lower around shoulder height. A tailored pattern can follow that transition with shaped panels and vertical seams. This produces a cleaner fit than forcing the chair into a simple cone or rectangular bag.

Plan the opening before choosing fasteners

A full-height egg chair cover can be awkward to lift over the suspension arm. A long zipper or split opening reduces the amount of fabric that must be raised above shoulder height. Place the opening where it can be reached easily without dragging the cover against a wall or planter.

For exposed patios, a drawcord, elastic hem, or buckle straps can help keep the lower edge close to the base. The fastening system should anchor around a stable part of the stand rather than pull against the hanging basket.

Use ventilation to manage residual moisture

Outdoor wicker and cushions should be dry before covering, but morning dew and humidity can still enter from below. Covered vents placed under protective flaps allow passive air exchange while helping block direct rain. A vent is especially useful on a deep egg-shaped shell because the interior air volume is larger than it appears.

Material also matters. Compare the handling weight, water resistance, and durability options on the CoversForge fabric guide. A frequently used chair may benefit from a lighter cover that is easy to remove, while a chair stored for long periods in an exposed area may need a heavier fabric and stronger tie-down details.

Prevent pooling at the crown and seat

A covered egg chair should present a smooth upper slope that guides rain away. Before covering, center the basket and arrange cushions so they do not create a low pocket in the seat. If the chair’s top is nearly flat, a simple support beneath the cover can create drainage, but it must be broad and smooth so it does not stress the fabric.

After the first rain, inspect the cover. If water remains in one area, adjust the chair position, cushion arrangement, or cover tension instead of allowing repeated pooling.

Create a repeatable remove-and-cover routine

1. Brush debris from the chair and confirm the wicker and cushions are dry.
2. Center the hanging basket and stop any movement.
3. Open the zipper or split panel fully before lowering the cover.
4. Guide the reinforced seams over the crown and widest curves.
5. Close the opening without forcing the zipper around a projection.
6. Secure the hem or straps to the stable base.

This routine reduces abrasion and makes it more likely that the cover will be used every day rather than left folded nearby.

What to send with a custom egg chair cover request

Include the overall dimensions, base footprint, basket size, suspension-arm offset, preferred opening location, and two clear photos. Mention whether cushions stay on the chair, how exposed the patio is, and how frequently the cover will be removed. For additional patio protection options, browse custom patio furniture covers.

When the chair has an unusual frame or limited installation clearance, add those details to a custom cover quote request. A cover designed around the real storage position will be easier to handle and more dependable than one based on the basket dimensions alone.